Enfield-Rifles.com Homepage
Forum Home Forum Home > Enfields > Enfield Gunsmithing
  New Posts New Posts RSS Feed - Is this hole supposed to be on a No4 Mk1/2 Bolt He
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Is this hole supposed to be on a No4 Mk1/2 Bolt He
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
BrandinC View Drop Down
Newbie
Newbie


Joined: December 12 2023
Location: United States
Status: Offline
Points: 5 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BrandinC Quote  Post ReplyReply Direct Link To This Post Topic: Is this hole supposed to be on a No4 Mk1/2 Bolt He
    Posted: December 22 2023 at 3:37pm
I'm trying to fit the extractor spring into the bolt head, but I can't seem to get the spring to stay in position while I fit the extractor. While examining the bolt head, I noticed this hole that lines up with the notch on the extractor spring, and I'm wondering if this hole is supposed to be drilled all the way through the bolt head to where the extractor spring is. This rifle is covered in grime and hasn't had any maintenance done in a while, so I can't tell if this is dirt or metal. Should I try to unplug this hole, or is it supposed to be like this? 
Back to Top
BrandinC View Drop Down
Newbie
Newbie


Joined: December 12 2023
Location: United States
Status: Offline
Points: 5 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BrandinC Quote  Post ReplyReply Direct Link To This Post Posted: December 25 2023 at 11:54am
Update: I figured it out, the hole is now clear and the new extractor spring had been installed. 
Back to Top
britrifles View Drop Down
Senior Member
Senior Member
Avatar

Joined: February 03 2018
Location: Georgia, USA
Status: Offline
Points: 8404 		Post Options Post Options   Thanks (1) Thanks(1)   Quote britrifles Quote  Post ReplyReply Direct Link To This Post Posted: December 26 2023 at 3:44am
Yes, the extractor spring has a small protrusion that fits into that hole, this is what retains the spring in the bolt head. I fit the extractor first, then the spring, tap it in place with a brass punch or flat head screwdriver from the forward side of the bolt head.  Remove it the same way by driving it out thru the opening in the back of the bolt head.  
Back to Top
Shamu View Drop Down
Admin Group
Admin Group
Avatar
Logo Designer / Donating Member

Joined: April 25 2007
Location: MD, USA.
Status: Offline
Points: 20510 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Shamu Quote  Post ReplyReply Direct Link To This Post Posted: December 26 2023 at 10:13am
You can also use a couple of loops of strong fishing line or dental floss to pull the spring in from the other end. Wrap it round a pencil or something similar to make a handle, grease it up & pull firmly. Thumbs Up
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)
Back to Top
martini1215 View Drop Down
Groupie
Groupie
Avatar

Joined: December 11 2023
Location: Cleethorpes
Status: Offline
Points: 90 		Post Options Post Options   Thanks (0) Thanks(0)   Quote martini1215 Quote  Post ReplyReply Direct Link To This Post Posted: December 29 2023 at 1:05am
I was just going to mention dental floss and saw your post Shamu.
I wrap mine round a small screwdriver handle to get some purchase, they slide in lovely.
Back to Top
Shamu View Drop Down
Admin Group
Admin Group
Avatar
Logo Designer / Donating Member

Joined: April 25 2007
Location: MD, USA.
Status: Offline
Points: 20510 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Shamu Quote  Post ReplyReply Direct Link To This Post Posted: December 30 2023 at 2:28pm
Great minds & all that stuff!
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.07
Copyright ©2001-2024 Web Wiz Ltd.