Print Page | Close Window

For the Sporterized Enfield enthusiasts.

Printed From: Enfield-Rifles.com
Category: Enfields
Forum Name: After Market Enfields
Forum Description: What have you done to that Enfield??
URL: http://www.enfield-rifles.com/forum_posts.asp?TID=12014
Printed Date: March 26 2026 at 7:18pm
Software Version: Web Wiz Forums 12.07 - https://www.webwizforums.com


Topic: For the Sporterized Enfield enthusiasts.
Posted By: Goosic
Subject: For the Sporterized Enfield enthusiasts.
Date Posted: May 12 2022 at 8:30am
.....Hug.....



Replies:
Posted By: Shamu
Date Posted: May 12 2022 at 10:45am
Nice!
how well did the synthetic stock fit? How did you bed the synthetic if it was needed?


-------------
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)


Posted By: Honkytonk
Date Posted: May 12 2022 at 11:55am
Love Sporters!


Posted By: Goosic
Date Posted: May 12 2022 at 2:10pm
Originally posted by Shamu Shamu wrote:

Nice!
how well did the synthetic stock fit? How did you bed the synthetic if it was needed?
The only minor modifications I made were to cut away the back section of the forend so it would fit around the block the trigger is hung to and then fitted a cross screw. The actual fit of the forend to the reciever and barrel required nothing special. A drop in procedure. 
There are very minor flaws/gaps but I can only assume that after so many iterations made from the original Sile stockset there is going to be a minor flaw somewhere. The magazine is my homemade Parker Hale clone...


Posted By: Shamu
Date Posted: May 13 2022 at 10:44am
A suggestion if I may.
Check out the angle between the front of the butt socket & the rear of the forend.
It may be a trick of the light but it seems to have bottom contact but a gap towards the  top?
You need full contact over 85% of the surface.
This is the biggest cause of beaten up draws. They are supposed to "draw" (force) the stock up & back as you tighten the main screw. Otherwise the draws take the firing shock, not the rear of the stock.


-------------
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)


Posted By: Goosic
Date Posted: May 13 2022 at 1:06pm
As far as the forend goes. There is is 100% contact where the bottom of the action rests. The King Screw has been tightened to 30 inch pounds. It has a hung trigger so the cross screw has been tightened to 18 inch pounds against the trigger block.
In an earlier post I mentioned that I've actually fired this rifle without the forend in place.  With or without the forend makes no difference in point of impact out to 100 yards.


Posted By: Shamu
Date Posted: May 13 2022 at 1:55pm
I'm thinking of the rear face, where it contacts the front face of the butt socket, not the bottom.
That is where the recoil forces are taken from the metal to the wood.


-------------
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)


Posted By: jshaf00
Date Posted: June 13 2022 at 2:42pm
The 2 work horses on the ranch :




Posted By: jshaf00
Date Posted: June 13 2022 at 2:48pm


Posted By: jshaf00
Date Posted: June 13 2022 at 2:52pm


Posted By: scottz63
Date Posted: June 14 2022 at 4:09am
Nice!

-------------
14EH AIT Instructor-PATRIOT Fire Control Enhanced Operator/Maintainer


Posted By: Enfield trader
Date Posted: June 14 2022 at 4:36am
Nice early cocking pieces


Posted By: jshaf00
Date Posted: June 14 2022 at 7:55am
Originally posted by Enfield trader Enfield trader wrote:

Nice early cocking pieces
 

Both are 1943 vintage savage #4 mk1*   both with near mint 2 groove barrels.  it was a shame someone had cut them down really.   found both at a pawn shop stuck in a corner covered in dust.  no one wanted them.   cleaned em up dressed em up and put them to good use.



Posted By: Goosic
Date Posted: June 14 2022 at 7:59am
Originally posted by Enfield trader Enfield trader wrote:

Nice early cocking pieces
I have those early button style cocking pieces because I simply cannot grip the later ones comfortably and reliably enough. The Maltby is my go to hunting rig and I feel it necessary to have reliable manual cocking just in case...



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.07 - https://www.webwizforums.com
Copyright ©2001-2024 Web Wiz Ltd. - https://www.webwiz.net